D-GC88Q FUEL DISPENSER

D-GC88Q FUEL DISPENSER

FlowMeter Type : Optional

Accuracy :±0.2%

Pressure Loss (kg/cm) :Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp): 1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition:-40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price :0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight : 450kg

Dimension(L×W×H) : 1615 X 620 X2420(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 26

ank and fuel dispenser. It is incomprehensive to think that the higher vacuum pressure in inlet the better performance. Here is vacuum pressure of pump inlet formula: PZ = Pa－P1= P gh＋P [(υ1)2/2 ] = P ghf (2-9) PZ ── vacuum pressure of pump inlet Pa── absolute atmospheric pressure P1── absolute pressure of pump inlet g── acceleration of gravity h── height from pump inlet to oil level in tank υ1── velocity of pump inlet hf── energy loss in pipe from tank to pump inlet from formula 2-9, there are three exterior conditions depend vacuum pressure of pump: pressure needed to lift oil, σgh; the pressure that used to increase flow velocity, P [(υ1)2/2 ]; the pressure loss in pipeline, P ghf . Once oil contains air, along with pressure decrease, more air is separated. So dose that along with inlet vacuum pressure increases. Under there conditions, cavitation would occur in pipeline, causing pump’s normal operation. In order to prevent above disadvantage effects, pay much attentions to installation of pipeline: ①tank should not be burred too deeply, the vertical distance from bottom valve to fuel dispenser no more than 4m, for example, regulated by some manufacturers with the purpose to prevent higher vacuum pressure of pump inlet; �?the diameter of pipe should not too small. As flow velocity correlate to section of pipeline, fuel dispenser vacuum pressure at inlet of pump will be increased when high velocity in smaller diameter pipe; adopt as few as elbow in pipeline, preventing the connection with different diam fuel dispenser eter pipe, adopt pipe with smooth pipe wall. Rational installation of pipeline between tank and fuel dispenser benefit avoiding cavition and reduce vacuum pressure of pump inlet, which is also conducive to deduct business cost and power consumption. The unreasonable pipeline installation not only results in suction difficulty but also easily generate no suction in hot whether, increasing power loss. The wrong installation also leads to larg fuel dispenser

les valeurs des champs sans signification pour ces exemples sont indiqu s par xxxx　　 12.5.1. Mise en place des canaux　　 Message mis par lautomate n�? supportant trois applicatifs (cas standard):　　Longueur Id canal Id Id N�? Statut Donn es messages Signature　　 application message transaction r ponse Nb. Applicatif Applicatif Applicatif　　 applic. 1 2 3　　 xxxx 0000 00 SX90 030000 0X40 0X40 0X03 CB0 EMV IS2 xxxx　　 R ponse du serveur mon tique supportant une application CB une application EMV et une　　 applications cartes ?piste avec la r partition des canaux suivante:　　 ID application ID canal　　 Applicatif N�?dapplication N�?automate N�?canal　　 Application 1 CB0 01 03 14　　 Application 2 fuel dispenser EMV 01 03 05　　 Application 3 IS2 01 03 fuel dispenser 06　　 Id canal Id Id N�? Statut　　 Longueur application message transaction r ponse　　 xxxx 0000 00 SX91 030000 0X40 0X40　　 Donn es messages　　 fuel dispenser

clumsy. But soon, Mr Payne believes, players will be able to customise the voices of their in-game alter egos. Now you re talking. © 2006 .  About sponsorship A meaty question Sep 21st 2006 From The Economist print edition Biotechnology Meat grown in vats, rather than in the form of animals, could soon be on the menu. It might even be healthier and better for you IF YOU have ever longed for a meat substitute that smelt and tasted like the real thing, but did not involve killing an animal, then your order could be ready soon. Researchers believe it will soon be possible to grow cultured meat in quantities large enough to offer the meat industry an alternative source of supply. Growing muscle cells (the main component of meat) in a nutrient broth is easy. The difficulty is persuading those cells to form something that resembles real meat. Paul Kosnik, the head of engineering at a firm called Tissue Genesis, is hoping to do it by stretching the cells with mechanical anchors. This encourages them to form small bundles surrounded by connective tissue, an arrangement similar to real muscle. Robert Dennis, a biomedical engineer at the University of North Carolina, believes the secret of growing healthy muscle tissue in a laboratory is to understand how it interacts fuel dispenser with its surroundings. In nature, tissues exist as elements in a larger system and they depend on other tissues for their survival. Without appropriate stimuli from their nei fuel dispenser ghbours they degenerate. Dr Dennis and his team have been working on these neighbourly interactions for the past three years and report some success in engineering two of the most important�? those between muscles and tendons, and muscles and nerves. At the Touro College School of Health Sciences in New York, Morris Benjaminson and his team are working on removing living tissue from fish, and then growing it in culture. This approach has the advantage that th fuel dispenser