D-GB66 FUEL DISPENSER

D-GB66 FUEL DISPENSER

Pump Type :Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.): 55±5

Suction Distance (m): 6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) 1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition :-40~~+55degree

Control Type : Solenold Vale Control Type

Preset :Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight :405kg

Dimension(L×W×H) :1270 x 620 x 2420(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 28 20ft: 13

Exploded drawing of double flux solenoid valve From above diagrams, it is known that this kind of solenoid valve consists mainly of valve body, membrane, cone-shaped spring, valve cover, pilot valve, fuel dispenser control valve of small flux, reposition valve, winding of pilot valve and small flux valve winding. The working principle of double flux solenoid valve can be leaned from Diagram 2-35. Pilot valve, small flux valve and main valve controlled by membrane are closed after power cut, no oil pass solenoid valve. When both two windings are open, pilot valve and small flux valve switch on, pressured oil pushing down membrane. Part of oil in A chamber flow toward outlet of solenoid valve via pilot valve and small flux valve, main valve is switched on after overcoming spring, at this state, solenoid valve is in large flux. When winding of pilot valve is cut power, pilot valve is closed, membrane go upward so as to close main valve due to oil pressure increase in A chamber. Solenoid valve is in small flux state. If the power of winding of small flux valve is cut off, small flux valve is closed, no flux in solenoid valve. It is learned from above introduction that the large and small flux of solenoid valve are controlled by pilot valve and small flux valve. This is why it called double flux solenoid valve. As filing motor, pilot valve, small flux valve and main valve are switched on, fuel dispenser work in large flux state. When filling volume nearly reach presetting value, windin fuel dispenser g power of pilot valve is cut off, main valve is closed. However, small flux valve is still working. When filling volume reach preset-value, the winding power of small flux valve is cut off, solenoid valve is closed. Filling operation is end. Troubleshooting In filing operation some troubles maybe correlate to solenoid valve, some maybe to other hydraulic components. Small flux or no delivery in fuel dispenser, for example, it is possible caused by solenoid valve or other components. Therefore, it is need to give concrete analysis and diagno fuel dispenser

itions.　　 The sample of test cable shall be prepared and fitted into the cable entry device in accordance with the entry　　 device manufacturers instructions and to t fuel dispenser he dimensions shown in Figure 8.　　 The conductor ends shall be suitably sealed so as to prevent any possibility of flame transmission between　　 conductor strands or between strands and insulation.　　 -- - - ---　　 33　　　　　　 Cable tails left unsecured shall be capped　　 off to seal from hot gases. Length 2 5 D1　　 where D1 = wire diameter including　　 insulation. Total length of wires　　 25 D1 �?10 %. If screened wi fuel dispenser res　　 screened part length is 2 5 D1. Diameter　　 of inner sheath is D2. Length of inner　　 sheath shall be equal to D2 �?10 %.　　 fuel dispenser

charges were it not for his presidential immunity. The army, which used to be highly politicised, is still believed to be a bastion of support for the opposition Nationalist Party, the Kuomintang ( fuel dispenser KMT). But there has been no hint of any military pressure on the president. Corruption allegations against Ma Ying-jeou (pictured above right), the KMT s chairman and present mayor of Taipei, surfaced in November, and helped deflect criticism from Mr Chen. The president s Democratic Progressive Party (DPP) is widely expected to lose the race for the Taipei mayorship to the KMT s Hau Lung-bin (above left). But opinion polls suggest the DPP s candidate, Frank Hsieh, still enjoys the support of traditional DPP voters in the capital. In Kaohsiung, a port city in the south, the contest is far closer. Mr Ma s travails appear to have boosted the chances of the DPP s Chen Chu, who spent six years in jail during the authoritarian era for her role in pro-democracy protests in Kaohsiung in 1979. Losing in Kaohsiung would be a setback for the DPP. But the city has never been a DPP stronghold. Votes usually split quite evenly. Half go to the DPP and other parties that likewise back Taiwan s formal independence from China, which still claims sovereignty. Half go to the KMT and others arguing for closer ties with China. Dachi Liao of Kaohsiung s National Sun Yat-sen University says both big parties have in fact been overstating the importance of these polls in order to r fuel dispenser ally supporters. Even if the KMT wins, Mr Chen is unlikely to waver in his apparent determination to stay in office until the end of his term in May 2008. Regardless of the outcome, the DPP will face big internal struggles as it prepares for the presidential elections. Choosing a candidate will be divisive. Possible contenders include Frank Hsieh as well as Su Tseng-chang, the prime minister, Yu Shyi-kun, the party s chairman, and Annette Lu, the vice-president. Mr Yu and possibly Mr Su would face pressure to resign should the DPP lose bo fuel dispenser