D-GAQ FUEL DISPENSER

D-GAQ FUEL DISPENSER

FlowMeter Type: Optional

Accuracy : ±0.2%

Pressure Loss (kg/cm) :Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle: Auto Shut-off Nozzle

Environmental Condition: -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price: 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer: 1~~9,999,999

Hose:4.5m

Weight :280kg.

Dimension(L×W×H) :900*620*2180(mm)

Dimension(L×W×H)Of Qty of Container: 40ft: 45 20ft: 22

but also container, vacuum pump. The hose made according to GB10543 consists of inner rubber layer, enhancing layer, conductible metal line and exterior rubber layer. Whichever hose abided by the requirements of GB/T9081-2001 Fuel dispenser for vehicle and JJG443-98 Fuel Dispenser in terms of safety and accuracy. During operation pay muc fuel dispenser h attention to protect hose: avoid as much crook as possible; prevent pressure on hose; avoid and reduce abrasion with ground. 4. Connection and seal about pipeline and hydraulic elements Each part of fuel dispenser adopts pipeline connection, dividing into hard type and soft type. In hard type connection steel pipe, brass pipe and aluminum pipe are adopted as pipeline, but in soft type one hose fuel dispenser and corrugated pipe. Connected components includes relative elbow jointer, flange and directive jointer. There are following seal types: cone-shaped seal, subulate thread seal, O-ring seal, rubber and asbestos gasket, cork and rubber board, engineering rubber board. According to regulation stipulated in GB/T9081 every fuel dispenser should be conducted sealability testing before leaving factory, no leakage found under normal operation. As replace some parts or found leakage these problems should be paid attention: Cone-shaped seal structure Cone-shaped seal structure also called as expanding jointer, which is composed of pipe with outstretched end, flat spout and outside thread bushing. Sealability is ensured through tightly integration of subulate surfaces. In disassembling or reassembling cone-shaped seal structure pays much attention not to hurt or broken sublatae surfaces, cleaning waste. Thread airproof As disconnection or reassembly thread surface should be kept clean, daubing seal glue or seal belt before installation. O-ring seal Most manufacturers adopts national standard to design O-ring seal, reaching a good sealability. However, some parts is impossible to adopt national standards because of specific structure. Thus, user should purchase or employ appropri fuel dispenser

itself (assuming that the PCD supports more than 1　　 transaction buffer).　　 As most proprietary FP s don t support assignment the PCD will have to manage　　 the assignment regulations itself.　　 Where the proprietary FP protocol doesn t indicate the fuel dispenser selected nozzle the PCD　　 will have no choice but to ignore the Log_Noz_Mask and release the FP.　　 Action : For preset or prepay mode the FP receives the　　 Remote_Volume_Preset or Remote_Amount_Prepay data.　　 The FP receives Release_FP command.　　 fuel dispenser Action : The FP state change is send as an unsolicited data array　　 FP_Status_Message .　　 NOZZLE-DOWN The customer returns the first selected logical nozzle into its holster and the FP　　 returns to the IDLE state. This allows the customer to select another logical nozzle　　 from the same FP if the wrong one has been picked up.　　 Action : The FP state change is send as an unsolicited data array　　 FP_Status_Message .　　FP31_2.23 IFSF - STANDARD FORECOURT PROTOCOL March 2006　　 DISPENSER APPLICATION　　Page: 38　　 TERMINATE_FP The FP is forced to move to the IDLE state.　　 PCD Comment:　　 As most proprietary FP s don t support the concept of terminating a CALLING　　 FP the PCD will have to manage the state transitions from CALLING to IDLE.　　 This action will involve dealing with the proprietary FP being IDLE but having its　　 nozzle removed.　〠fuel dispenser

mits, in today s cars. Biodiesel fuelling stations, such as those for BioWillie, are popping up around America. All is not perfect. Ethanol is typically blended with regular fuel, and a widespread switchover to an ethanol blend (a result of another provision of last year s energy bill) has contributed to some petrol shortages in Texas a fuel dispenser nd elsewhere, as the supply chain creaks into life. Sceptics argue that growing crops for ethanol will burn more petrol than it will save. But others are persuaded, despite the teething pains. “If I had to bet 100 bucks, I d bet on biofuels,�says Hunter Lovins, co-author of “Natural Capitalism� adding that she would favour them even over plug-in hybrids and hydrogen fuel cells. Rich investors a fuel dispenser re also bullish. Richard Branson, a British entrepreneur who heads the Virgin conglomerate, recently announced plans to invest up to $400m in ethanol production. Can production be scaled up? A recent bioengineering breakthrough means that it should soon be possible to convert plant products far more efficiently to ethanol. This lends promise to cellulosic ethanol—a product that can be made from agricultural “waste� such as corn cobs or weeds, which is widely available. (Once corn kernels and sugar-cane sap have been taken away for sugar, they leave plenty of stalks and leaves behind.) The most promising source of cellulosic ethanol, say experts, is switchgrass, a native American grass that grows naturally in the prairie heartland and thrives in the poor Mississippi Delta. Biodiesel, as yet, is a smaller enterprise. Its plants require less capital than those for ethanol. It is growing fast—sales volume tripled, to 75m gallons, between 2004 and 2005—but that is still a drop in the tanker of the 60 billion gallons of diesel that Americans consume each year. Much of the stuff is made from soyabeans, and Jeff Plowman of Austin Biofuels, a tiny start-up, notes that soyabean futures are tracking the price of heating oil for the first time. In Texas, M fuel dispenser